home contact

Thursday, December 12th, 2024 02:24 am

Synth Glossary

Envelope:
An envelope generator generates a signal that changes through the length of a sound, normally to control the loudness of that sound. An example of its use is to control the volume of a piano sound. It creates a signal that goes from low to high very quickly (the loud bit when the key is pressed), then goes down slowly as the sounds gets quieter. They are also used to drive other parts of the synthesizer, for example the filter....

more...




ADSR
A type of envelope generator. It has four stages - the attack of the note where it build up to its initial volume peak when you press the key, the decay where it goes back down in volume to the sustain level where it stays until the player releases the key and it fades out.
Additive Synthesis
A system for generating waveforms or sounds by combining basic waveforms or sampled sounds prior to further processing with filters and envelope shapers.
Aftertouch
A means of generating a control signal based on how much pressure is applied to the keys of a MIDI keyboard. Most instruments that support this do not have independent pressure sensing for all keys, but rather detect the overall pressure by means of a sensing strip running beneath the keys. Aftertouch may be used to control such functions as vibrato depth, filter brightness, loudness and so on.
Amplifier
The part of the synthesizer that amplifies the sound that is generated by the oscillator. It normally has a control input which affects the level of amplification and which is normally be driven by an envelope or an LFO.
Analog Synthesis
This term is normally used to refer to the tradional synthesis model used by analog synthesizers in the 1970s. It is also known as subtractive synthesis. It involves oscillators, the outputs of which are mixed together and fed into a filter (where certain frequencies are subtracted) after which they are fed through an amplifier. The amplifier and filter are normally also driven by envelope generators.
Arpeggiator
Many synths can only play one note at a time (they are monophonic). With the arpeggiator on, if more than one note is pressed at a time, the synth will alternate between the notes. They also often have a range control that allows the user to tell the ynth to play additional octaves - so if the range is set to two octaves the synth will play the keys that are held down in the octave that they are played and then in the next octave up/down.
Attack
The time taken for a sound to achieve maximum amplitude. Drums have a fast attack, whereas bowed strings have a slow attack. In compressors and gates, the attack time equates to how quickly the processor can change its gain.
BPF
A type of filter. A band-pass filter only allows through a selected band of frequencies in the middle of the frequency range. It is not used very much.
BPM
Beats Per Minute.
Control input
An input into part of the synthesizer that allows that bit to be modulated by another part of the synth. For example there is a control input in the amplifier which controls the level of amplification. If a very slow sine wave (an LFO) is patched into this input then the sound will slowly get louder and quieter. If an LFO was patched into the control input of the oscillator instead, then the sound would go higher and lower in pitch.
Cross-modulation
This is the ability for parts of a synthesizer to be able to modulate other parts of the synthesizer. The synths with most cross-modulation abilities are modular synths, which actually use patch leads to plug different modules into each other, so any output can be plugged into any input.
Envelope
An envelope generator generates a signal that changes through the length of a sound, normally to control the loudness of that sound. An example of its use is to control the volume of a piano sound. It creates a signal that goes from low to high very quickly (the loud bit when the key is pressed), then goes down slowly as the sounds gets quieter. They are also used to drive other parts of the synthesizer, for example the filter.
Filter
A filter filters out certain frequencies in the sound. There are four main types: a low-pass, high-pass, band-pass and notch, which are covered elseware in the glossary. Filters have two controls - the frequency control selects at which frequency the filter should start operating and the resonance control creates a peak just before the bit where it starts filtering out frequencies. This is used to create acid-type sounds.
Frequency Modulation (FM)
Frequency modulation allows the output of one oscillator to drive the frequency of another oscillator. It can generate very complex sounds from very simple waveforms and is the basis of the Yamaha DX range of synthisizers and OPL range of synthesizer chips (used in Adlib and most other soundcards).
Granular Synthesis
The sound is split into small chunks called granules. These may then be processed in various ways to acheive various effects - for example, to stretch a sound (timestreching) the granules will be played back so as to overlap each other. An interesting effect can also be obtained by playing the granules backwards.
HPF
A high-pass filter filters out lower frequencies from the sound.
LFO
A Low Frequency Oscillator. It is similar to a normal oscillator except that it outputs very low frequencies (very slow waves) and is used as a control input into another part of the synth. Examples of its use are to create vibrato or tremolo effects.
Latency
The delay between a control being turned or a key being pressed and hearing the result in the output. Hardware synths have almost zero latency - but many software synths have a lag.
Low-pass
A low-pass filter filters out higher frequencies from the sound.
Midi
An interface for connecting musical instruments together. It is used to connect musical keyboards to the PC and can also be used for connecting together music programs inside the PC.
Modular
A modular synthesizer is one where the structure of the synthesizer isn't fixed. There are a variety of modules available which can be plugged into each other. Tradionally these modules were physical boxes, but they can now be emulated with software and patched with on-screen cables.
Monophonic
If a synth is monophonic, it can only play one note at a time. Contrast with polyphonic.
Oscillator
An oscillator produces a pure sound. The frequency (i.e. pitch) and waveform (e.g. sine waves or square waves) of the sound can be selected.
PWM
Pulse Code Modulation is the ability to modulate the pulse width in a square/pulse wave. (NB: A pulse wave is a square wave with 50% pulse width)
Physical Modelling
Physical modelling is a method of synthesis in which a mathematical model of the instrument being synthesized is used to create the sound. It is the best way of approximating a real instrument.
Polyphonic
A polyphonic synth can play several notes at the same time.
Resonance
Most filters can emphasize the frequencies just before those that are reduced in volume. Resonance is the degree of emphasis that occurs. It makes the filter much more audible and gives it character - it would otherwise sound like just altering the equalisation - and is the foundation of the acid sound.
Ring Modulator
Takes two sounds as its input (e.g. from two oscillators) and takes their difference to create a new sound, normally metallic sounding.
Timbrality
The number of different timbres (instruments) a synthesizer can play at a time. Some synthesizers are polyphonic but only monotimbral - ie they can play several sounds but only in the same instrument.

Hosted by Jesse Mullan